Remodeling & Upgrades · Lawrence, KS

Tile Shower Installation in Lawrence, KS — Professional Service

Tile shower installation in Lawrence, KS. Sheet and liquid membrane systems, sloped mortar pans, bonded-flange drains, large-format layout and grout that holds up. Built to be flood-tested.

877-519-9702

Call for a free estimate — no obligation

Free Estimates

Written Price First

Handyman combing thinset with a notched trowel and setting wall tile over waterproofing board beside a linear drain in a Lawrence, KS shower under construction

Same-Day Estimates

Upfront Pricing

Mon–Sat Availability

About This Service

Expert Tile Shower Installation in Lawrence, KS

Tile shower installation runs $4,800 to $12,000, and the money is not in the tile. It is in the system underneath, the pan, the slope, the membrane and the drain, because that is what determines whether the shower is still dry in fifteen years or quietly feeding water into the framing. We build tiled showers as a waterproofing assembly first and a finish surface second, and we flood-test the pan before a single tile goes on the wall.

Tile is not waterproof, and cement backer board is water-durable but not waterproof either, meaning it survives being wet without rotting while water travels straight through it. A tiled shower stays dry because a continuous membrane sits between the tile assembly and the structure, and every corner, seam, fastener and pipe penetration is sealed into that same membrane. This matters more in some parts of Lawrence than others: homes closer to the Kansas River corridor north of downtown carry a higher ambient humidity load, and a bathroom in one of those homes never quite gets the drying cycle between showers that a drier house does. A fully continuous, single-manufacturer membrane system is genuinely more important there than in a house further from the river.

The pan is where the craft concentrates. In a traditional mud-bed build there are two mortar beds, not one, a pre-slope under the membrane so any water reaching the liner is carried to the weep holes, then the liner, then the top bed. Slope is a quarter inch of fall per foot toward the drain, enough to move water, gentle enough to stand on. A linear drain set along one wall changes the geometry usefully, allowing the whole floor to fall in a single direction, which is what allows large-format tile without awkward wedge cuts.

Layout is a decision, not a default. We lay out from the sightline, the wall you see when you walk in and the niche you look at every day, so the cuts land in the least visible corner. We handle demolition, framing and blocking, backer board, sheet and liquid membrane systems, mortar bed and foam pans, tile setting, niches, benches, grout and sealant, and we flood-test the pan for 24 hours before tile. Call 877-519-9702 for a free tile shower installation estimate.

Sheet & Liquid Membrane Systems

Sloped Mortar Bed Pans

Large-Format & Niche Detailing

Flood-Tested Before Tile

Get a Free Estimate

Call us directly for a fast, no-obligation estimate on your tile shower installation project.

877-519-9702

Mon–Fri 7am–6pm · Sat 8am–2pm

Written estimate before work starts

Our Process

How We Handle Tile Shower Installation

Build a Flat, Solid Substrate

Studs are checked for plane, blocking goes in for niches and benches, and the backer board is set with the right fastener spacing, tile telegraphs everything underneath it.

Pan First, Then Membrane, Then Flood Test

Pre-slope, drain type and membrane all get built as one system at a quarter inch of fall per foot, and the pan holds water for 24 hours before a single tile is set.

Lay Out From the Sightlines

Layout starts from the wall you see first and the niche, not from a corner, so cuts land where they are least visible and the niche courses line through.

Set, Grout and Cure on Schedule

Full thinset coverage on wet-area tile, grout after the setting mortar cures, silicone at every change of plane, and a firm date when the shower can be used.

FAQ

Tile Shower Installation Questions Answered

Common questions from Lawrence homeowners about our tile shower installation service.

Still have questions?

Call us — no forms, no queue. 877-519-9702

How is tile shower installation different from a shower remodel?

Our shower remodel service covers the project-level decisions, whether to convert a tub, where the drain sits, whether the entry stays curbed. This page is about the craft of the tiled shower itself: which waterproofing system goes on, how the pan gets built and sloped, and how the tile is laid out and set.

Which waterproofing system is best for a tile shower?

Both proven approaches work when installed completely. A bonded sheet membrane is waterproof the moment it is on, so tile can follow the same day. A liquid-applied membrane is rolled on in coats and has to reach the manufacturer specified thickness and cure before tile. What matters more than the choice is that one system is used throughout.

Do you use a mortar bed pan or a foam pan?

Both, depending on the shower. A traditional mortar bed pan lets us match any size, shape and drain position. A pre-sloped foam pan bonded to the subfloor is faster, dimensionally exact, and eliminates the two most common site errors, missing pre-slope and inconsistent fall.

Why does grout crack in the corners of a shower?

Because grout is a rigid cement product being asked to bridge a joint that moves. Every inside corner belongs in flexible sealant, silicone matched to the grout color, not grout.

Does Lawrence's river-corridor humidity make waterproofing more important?

It does. Homes closer to the Kansas River corridor north of downtown carry a higher ambient humidity load than the rest of the city, and a bathroom in one of those homes never quite gets the same drying cycle between showers that a drier house does. That makes a fully continuous membrane system, rather than a partial or shortcut waterproofing job, genuinely more important there than elsewhere in Lawrence.

Pricing Guide

Tile Shower Installation Cost in Lawrence, KS

Tile shower installation in Lawrence typically runs: standard alcove tiled shower with a pre-sloped foam pan, a bonded membrane system and mid-range tile $4,800–$8,200; the same shower built on a traditional two-bed mortar pan $5,600–$9,400; a larger or non-standard footprint with a linear drain $7,200–$12,000; a curbless entry where the pan is recessed into the floor framing $9,000–$15,000, quoted after the joists are evaluated.

A waterproofed tiled niche runs $250–$500. A framed, membraned and tiled bench runs $400–$850. Upgrading from cementitious to epoxy grout runs $2.50–$5.00 per square foot. Free estimates. Call 877-519-9702.